从 bfflist 获取 tirzepatide 45 mg
有人有过这种反应吗？
- Thread starter JAYB820
- Start date
- Status
AMO（这是该供应商的原名）会在他们的药瓶中添加某种物质，偶尔会导致这种情况发生。
何
你们是怎么处理的？换新的试管？下次多加点抑菌水？我这次只加了100单位（1支注射器）的抑菌水……下次多加点能稀释一下吗？Gamma662keV said:
我认为，正如你在另一个帖子中提到的，不使用 1 毫升 BAC 来配制 45 毫克 L60 会有很大帮助。JAYB820 said:
可能性很多，但 amo/bff 的可能性最小，因为它被广泛使用，而且在过去 6 个月多的时间里都没有出现过刺痛感的报告。
我目前每周注射 12.5 毫克 L60。
其他可能性还有很多，以下是一些相关的帖子：
查询结果：isr tirz
glp1forum.com
好的
非常感谢。您觉得使用3份100单位的杀菌水会有帮助吗？Skidude said:
tough to say, i dont know what you are pinning or what caused this.JAYB820 said:
If you are pinning 15mg you could easily put 1.5 ml/cc
but that reaction from tirz does not appear to be a concentration problem, i don't claim to be an expert but i have pinned a bunch.
That looks like either something in the water/something on the skin/cleaning was not done properly, bad BAC, or as you said in one of the many other threads you have on this- not related at all to the tirz and the prednisone will clear it up.
Did you tell telehealth you are using tirz? did they comment?
you might want to pick one thread and ask all there, you will get as better picture.
edited for typos
Ok thanks! Sorry new to thread and figure it out. I have 45 mg of tirzepatideSkidude said:
I have also done sema for months through compounded pharmacies and never had an issue
Currently pinning 6.25 units … and thanks again. I want to figure this out and before I pin again…. May try new bac water
Personally I find that reconstituting towards achieving a fluid volume in the .2-.5ml range is usually best for most peptides.
More fluid volume also results in more accurate dosing.
More fluid volume also results in more accurate dosing.
ZippityDooDah said:
Thank you and thank you for your patience as I navigate this site! I’m doing my best ! Has this reaction ever happened to you? I think it’s either bad bac water or not enough bac water for 45 mg of tirz and injecting 6.25 units just finished week 4
Using 100 units of water. One syringe full to mix tirzJAYB820 said:
I've never had any real ISR's (injection site reactions). About the worst I've ever had was a little PIP (post-injection pain) and on a handful of occasions a little temporary itching.JAYB820 said:
Anything other than Hospira BAC (or some of the more reliable Chinese), including the mystery bathtub waters - especially from the Amazonian Empire - is always a risk IMHO, but if you used the name-brand stuff I would easily rule that out.
The high concentration may have played a part, or it could be something as simple as your body over-reacting to the needle puncture itself or a number of other little things. Compared to others I've seen it looks pretty mild so as long as it clears up I wouldn't worry about it too much.
One of the things I learned early on in this adventure was to invest in some 3ml syringes and needles (25 gauge) to use for reconstitution. It makes the process easier and faster since a larger bore needle moves a lot more fluid a lot faster than a 30 or 31 gauge insulin syringe, and it makes using more than 1ml of fluid to reconstitute a one-step process and probably a bit more accurate.
Good to know thank you so much it’s been working wonders I’d hate to stop over a mild reaction. It’s usually gone in 3/4 days….
I ordered my bac water from research peptides. I’ll research and see if anyone else had reactions..
I did hear hospira brand is good. If it is the bac water I’ll order the hospira brand next before I mix my next vial .
I may try injecting just a tiny bit of bac water to see if that’s it… if not, I’ll order new needles and add more bac water to my next new vial. Thanks so much
I ordered my bac water from research peptides. I’ll research and see if anyone else had reactions..
I did hear hospira brand is good. If it is the bac water I’ll order the hospira brand next before I mix my next vial .
I may try injecting just a tiny bit of bac water to see if that’s it… if not, I’ll order new needles and add more bac water to my next new vial. Thanks so much
For tirz, my doses are always with 45u-50u of bac, just like Eli Lilly use (yes, half of the syringe). I don't see how you can be using a precision of 6.25u? Tell me more about the syringe? a 0.3cc? I barely can see the difference between 45u and 46u on my 1cc syringe. And yes, inject 10-20u of bac by itself to see if you get isr. Can also try 90 degree pin angle in fattest belly spot. When I stack other peptides in the same syringe, I sometime end up injecting up to 75u in one place. I never use less than 25u for injecting any peps. Bac is cheap. That is just me.
Hope this helps!
Don't know if it is allowed to link this but I use this bacwater calculator for my tirz
How Much Bacteriostatic Water to Add to Peptides? - Prime Peptides™
This article aims to guide you through the process of determining the correct amount of bacteriostatic water to use for your peptide
primepeptides.co
How Much Bacteriostatic Water to Add to Peptides? - Prime Peptides™
This article aims to guide you through the process of determining the correct amount of bacteriostatic water to use for your peptide
primepeptides.co
6.25 units tells us nothing. Mg. Use mg.JAYB820 said:
It's fine, but jeez they really went out of their way to make something relatively simple seem unnecessarily convoluted.m1tkam said:
It's also a good indicator that the owner of that shop isn't very bright. The history of the FDA going after peptide vendors is rife with examples of them targeting the low-hanging fruit of vendors openly discussing human use despite slapping the 'ol "research use only, not for human use" labels all over the place.
- Status
